top of page
F3 Aux Led Light Install Instructions

Step 1. Disconnect the battery

  • Remove the plastic cover above your trunk compartment and the 4 plastic rivets holding your trunk box in place.

  • You can now remove the trunk box by lifting it straight up.This will allow you to get to the battery.

  • Discount the battery.

IMG_3408.JPG
IMG_3410.JPG
IMG_3407.JPG

Step 2. Install Toggle Switch

  • Remove the key switch cover by twisting it to the left and pulling out

  • Next remove the dash panel by lifting up on it slowly, disconnecting the wires plugged into any switches or future blank spots. You will use the right side wires for the new switch.

IMG_3412.JPG
IMG_3414.JPG
IMG_3416.JPG
IMG_3417.JPG
IMG_3418.JPG

  • Remove the right side future switch blank from the dash cover, (The switch will only work in the right side hole)

  • Install the new switch into the dash cover, then secure the switch with the nut lug

IMG_3420.JPG
IMG_3425.JPG
IMG_3426.JPG

  • Connect the wiring harness to the switch. The harness will only fit on the switch one way. Double check you have them lined up correctly before connection them together. You should not have to force the switch and the harness together. 

  • Then connect the wiring harness to the right side plug. Gently feed the extra wire slack down into the dash

  • Attach the left side wires back to its original location, then reinstall the dash panel and key switch cover

IMG_3429.JPG
IMG_3430.JPG
IMG_3434.JPG
IMG_3435.JPG

Step 3

Remove Side Panel

  • Remove upper side cover

IMG_3437.JPG
IMG_3439.JPG

Remove the side panel

  • Remove the 3 plastic rivets on top, then remove the 2 torques bolts towards the front of panel and the 2 towards the back.

IMG_3445.JPG
IMG_3446.JPG
IMG_3443.JPG

​

  • Next you need to remove the plastic auxiliary light dummy blank. There is 1 screw holding this in place.

IMG_3447.JPG
IMG_3455.JPG

Step 4

Mount Lights

  • First you will need to mount the light backer plate. The plates are universal. They can be install on the left or right side. However, you will need to make sure they are mounted correctly as the center hole should not be in the center. The center hole should be slightly above center as shown below. If the hole is slightly below center you need to flip the backer plate over. Once you install the LED Light, the hole will become centered

  • Hold the plate over the mounting holes and fasten it to the bike using 3 3/8x1 bolts, followed by washers, lock washer, and nuts

IMG_3457.JPG
IMG_3459.JPG
IMG_3461.JPG
IMG_3462.JPG

​

  • Mount the Led Light to the backer plate using the 5/16 bolts.

  • The light bracket is offset, Mount  the light so it is offset downwards. This will counter the backer plate hole being above center . The light should now be centered in the bikes light fixture.

IMG_3463.JPG
IMG_3467.JPG
IMG_3464.JPG
IMG_3469.JPG
IMG_3466.JPG

​

  • Remove the cap from the prewired light plug. Then plug in the new lights.

  • You can disregard the cap.

IMG_3470.JPG
IMG_3473.JPG

Step 5

Tests and adjust lights

  • These instructions only show you how to install on the left side of bike. Repeater the process for the right side.

  • After finishing the install on the right side reconnect the battery and test the lights.

  • The light on the switch will stay on whether the lights are ON or OFF

  • If your lights are not working , the first thing to check is that your accessory fuse is installed and/or not blown. Some models came from the factory with the fuse not install.

  • We recommend using a wall or garage door to adjust your light.

  • Once you have the light where you want them, them reinstall all your side panels.

IMG_3480.JPG
IMG_3500.JPG

Thank you again for your purchase! If you need any help please give us a call.

bottom of page